哪里做网站域名不用备案摄影网页设计模板

当前位置： 首页 > news >正文

哪里做网站域名不用备案,摄影网页设计模板,国内大型餐饮网站建设,logo网站[调试] JTAG下运行正常#xff0c;从QSPI或者SD卡启动则无响应#xff0c;如何查找问题 一、问题现象二、用自定义fsbl替代系统默认的fsbl1. 新建fsbl_new2. 如果提示缺少xilffs库3. 使能调试信息输出 三. 启动成功和失败情况下的典型输出1. JTAG启动模式: 正常加载2. QSPI启… [调试] JTAG下运行正常从QSPI或者SD卡启动则无响应如何查找问题 一、问题现象二、用自定义fsbl替代系统默认的fsbl1. 新建fsbl_new2. 如果提示缺少xilffs库3. 使能调试信息输出 三. 启动成功和失败情况下的典型输出1. JTAG启动模式: 正常加载2. QSPI启动模式2.1 正常加载: flash已经烧写正常运行的程序启动模式QSPI2.2. QSPI错误加载的例子 3. SD卡启动模式3.1 SD正常启动3.2 没插卡或者卡检测失败3.3 找到文件但是文件错误 一、问题现象 用jtag在ide里面调试运行都正常。 生成boot.bin烧写到flash后上电pl done不亮串口无打印输出 二、用自定义fsbl替代系统默认的fsbl

1. 新建fsbl_new 新建一个app选择Zynq FSBL模板。
   
2. 如果提示缺少xilffs库 在上面的情况有可能会提示bsp缺少xilffs库。 这时候返回到bsp界面勾选添加缺少的库并重新编译全部工程。再执行上面的新建步骤 3. 使能调试信息输出 打开新建的工程找到fsbl_debug.h 可以看到#if defined (FSBL_DEBUG_INFO)这行 只要我们定义了FSBL_DEBUG_INFO就会输出完整调试信息 因此在36行增加 #define FSBL_DEBUG_INFO然后重新编译fsbl_new
   三. 启动成功和失败情况下的典型输出
3. JTAG启动模式: 正常加载 把启动模式切换到JTAG然后运行fsbl_new结果如下 Xilinx First Stage Boot Loader Release 2020.1 Jul 2 2024-12:27:50 Devcfg driver initialized Silicon Version 3.1 Boot mode is JTAG2. QSPI启动模式 2.1 正常加载: flash已经烧写正常运行的程序启动模式QSPI 先烧写QSPI然后断电把启动模式切换到JTAG。重新上电在Vitis里面运行fsbl_new结果如下 Xilinx First Stage Boot Loader Release 2020.1 Jul 2 2024-12:27:50 Devcfg driver initialized Silicon Version 3.1 Boot mode is QSPI Single Flash Information FlashID0x1 0x20 0x18 SPANSION 128M Bits QSPI is in Dual Parallel connection QSPI Init Done Flash Base Address: 0xFC000000 Reboot status register: 0x60500000 Multiboot Register: 0x0000C000 Image Start Address: 0x00000000 Partition Header Offset:0x00000C80 Partition Count: 3 Partition Number: 1 Header Dump Image Word Len: 0x00080B00 Data Word Len: 0x00080B00 Partition Word Len:0x00080B00 Load Addr: 0x00000000 Exec Addr: 0x00000000 Partition Start: 0x000065D0 Partition Attr: 0x00000020 Partition Checksum Offset: 0x00000000 Section Count: 0x00000001 Checksum: 0xFFE776BE Bitstream In FsblHookBeforeBitstreamDload function PCAP:StatusReg 0x40000F30 PCAP:device ready PCAP:Clear done Level Shifter Value 0xA Devcfg Status register 0x40000A30 PCAP:Fabric is Initialized done PCAP register dump: PCAP CTRL 0xF8007000: 0x4C00E07F PCAP LOCK 0xF8007004: 0x0000001A PCAP CONFIG 0xF8007008: 0x00000508 PCAP ISR 0xF800700C: 0x5802000F PCAP IMR 0xF8007010: 0xFFFFFFFF PCAP STATUS 0xF8007014: 0x00000A30 PCAP DMA SRC ADDR 0xF8007018: 0xFC019741 PCAP DMA DEST ADDR 0xF800701C: 0xFFFFFFFF PCAP DMA SRC LEN 0xF8007020: 0x00080B00 PCAP DMA DEST LEN 0xF8007024: 0x00080B00 PCAP ROM SHADOW CTRL 0xF8007028: 0xFFFFFFFF PCAP MBOOT 0xF800702C: 0x0000C000 PCAP SW ID 0xF8007030: 0x00000000 PCAP UNLOCK 0xF8007034: 0x757BDF0D PCAP MCTRL 0xF8007080: 0x30800100 ……………………………………………………………………………………… DMA Done ! FPGA Done ! In FsblHookAfterBitstreamDload function Partition Number: 2 Header Dump Image Word Len: 0x00002002 Data Word Len: 0x00002002 Partition Word Len:0x00002002 Load Addr: 0x00100000 Exec Addr: 0x00100000 Partition Start: 0x000870D0 Partition Attr: 0x00000010 Partition Checksum Offset: 0x00000000 Section Count: 0x00000001 Checksum: 0xFFD72CB8 Application PCAP:StatusReg 0x40000F30 PCAP:device ready PCAP:Clear done PCAP register dump: PCAP CTRL 0xF8007000: 0x4C00E07F PCAP LOCK 0xF8007004: 0x0000001A PCAP CONFIG 0xF8007008: 0x00000508 PCAP ISR 0xF800700C: 0x00033004 PCAP IMR 0xF8007010: 0xFFFFFFFF PCAP STATUS 0xF8007014: 0x50000F30 PCAP DMA SRC ADDR 0xF8007018: 0xFC21C341 PCAP DMA DEST ADDR 0xF800701C: 0x00100001 PCAP DMA SRC LEN 0xF8007020: 0x00002002 PCAP DMA DEST LEN 0xF8007024: 0x00002002 PCAP ROM SHADOW CTRL 0xF8007028: 0xFFFFFFFF PCAP MBOOT 0xF800702C: 0x0000C000 PCAP SW ID 0xF8007030: 0x00000000 PCAP UNLOCK 0xF8007034: 0x757BDF0D PCAP MCTRL 0xF8007080: 0x30800110DMA Done ! Handoff Address: 0x00100000 In FsblHookBeforeHandoff function SUCCESSFUL_HANDOFF FSBL Status 0x12.2. QSPI错误加载的例子 给QSPI烧写一个错误的文件。然后运行 Xilinx First Stage Boot Loader Release 2020.1 Jul 2 2024-12:27:50 Devcfg driver initialized Silicon Version 3.1 Boot mode is QSPI Single Flash Information FlashID0x1 0x20 0x18 SPANSION 128M Bits QSPI is in Dual Parallel connection QSPI Init Done Flash Base Address: 0xFC000000 Reboot status register: 0xF058200C Multiboot Register: 0x0000C400 //这里识别错误C400对应到flash的末尾了。正常应该是C000 Image Start Address: 0x02000000 //这里计算出的偏移地址已经超过了flash肯定无法读出正常的程序 DATA_ABORT_HANDLER //报错数据异常 FSBL Status 0xA304 //在fsbl.h里面可以查到对应的宏定义#define EXCEPTION_ID_DATA_ABORT_INT 0xA304 /** Data Abort Exception /搜到Multiboot Register可以搜到下面的代码可以看到是由于没搜到正确的boot导致MultiBootReg的值不正确。 /** read the multiboot register/MultiBootReg XDcfg_ReadReg(DcfgInstPtr-Config.BaseAddr,XDCFG_MULTIBOOT_ADDR_OFFSET);fsbl_printf(DEBUG_INFO,Multiboot Register: 0x%08lx\r\n,MultiBootReg);/** Compute the image start address/ImageStartAddress (MultiBootReg PCAP_MBOOT_REG_REBOOT_OFFSET_MASK) GOLDEN_IMAGE_OFFSET;3. SD卡启动模式 3.1 SD正常启动 Xilinx First Stage Boot Loader Release 2020.1 Jul 2 2024-12:27:50 Devcfg driver initialized Silicon Version 3.1 Boot mode is SD SD: rc 0 SD Init Done //卡初始化完成 Flash Base Address: 0xE0100000 Reboot status register: 0x60500000 Multiboot Register: 0x0000C000 Image Start Address: 0x00000000 Partition Header Offset:0x00000C80 Partition Count: 3 Partition Number: 1 Header Dump //解析到正确的镜像 Image Word Len: 0x00080B00 Data Word Len: 0x00080B00 Partition Word Len:0x00080B00 Load Addr: 0x00000000 Exec Addr: 0x00000000 Partition Start: 0x000075D0 Partition Attr: 0x00000020 Partition Checksum Offset: 0x00000000 Section Count: 0x00000001 Checksum: 0xFFE766BE Bitstream In FsblHookBeforeBitstreamDload function PCAP:StatusReg 0x40000F30 PCAP:device ready PCAP:Clear done Level Shifter Value 0xA Devcfg Status register 0x40000A30 PCAP:Fabric is Initialized done PCAP register dump: PCAP CTRL 0xF8007000: 0x4C00E07F PCAP LOCK 0xF8007004: 0x0000001A PCAP CONFIG 0xF8007008: 0x00000508 PCAP ISR 0xF800700C: 0x5802000F PCAP IMR 0xF8007010: 0xFFFFFFFF PCAP STATUS 0xF8007014: 0x00000F30 PCAP DMA SRC ADDR 0xF8007018: 0x00100001 PCAP DMA DEST ADDR 0xF800701C: 0xFFFFFFFF PCAP DMA SRC LEN 0xF8007020: 0x00080B00 PCAP DMA DEST LEN 0xF8007024: 0x00080B00 PCAP ROM SHADOW CTRL 0xF8007028: 0xFFFFFFFF PCAP MBOOT 0xF800702C: 0x0000C000 PCAP SW ID 0xF8007030: 0x00000000 PCAP UNLOCK 0xF8007034: 0x757BDF0D PCAP MCTRL 0xF8007080: 0x30800100DMA Done ! FPGA Done ! In FsblHookAfterBitstreamDload function Partition Number: 2 Header Dump Image Word Len: 0x00002002 Data Word Len: 0x00002002 Partition Word Len:0x00002002 Load Addr: 0x00100000 Exec Addr: 0x00100000 Partition Start: 0x000880D0 Partition Attr: 0x00000010 Partition Checksum Offset: 0x00000000 Section Count: 0x00000001 Checksum: 0xFFD71CB8 Application Handoff Address: 0x00100000 In FsblHookBeforeHandoff function SUCCESSFUL_HANDOFF FSBL Status 0x1 3.2 没插卡或者卡检测失败 Xilinx First Stage Boot Loader Release 2020.1 Jul 2 2024-12:27:50 Devcfg driver initialized Silicon Version 3.1 Boot mode is SD SD: rc 0 SD: Unable to open file BOOT.BIN: 3SD_INIT_FAIL FSBL Status 0xA009This Boot Mode Doesnt Support Fallback In FsblHookFallback function 3.3 找到文件但是文件错误 Xilinx First Stage Boot Loader Release 2020.1 Jul 2 2024-12:27:50 Devcfg driver initialized Silicon Version 3.1 Boot mode is SD SD: rc 0 SD Init Done Flash Base Address: 0xE0100000 Reboot status register: 0x6050200A Multiboot Register: 0x0000C001 Image Start Address: 0x00008000 Partition Header Offset:0xE8BE0070 Partition Count: 14 Invalid Partition Count Partition Header Load Failed FSBL Status 0xA00EThis Boot Mode Doesnt Support Fallback In FsblHookFallback function